How To Repair Blind Cord

Download Article

Download Article

Roller blinds are easy to apply and install. They are corking for providing deep, dark shade. Sometimes, however, the cord or concatenation may come up loose; other times it may become worn and need to be replaced. Luckily, it is piece of cake to replace the chain or cord. Go on in mind that while every model and brand will be a little different, the general process volition be mostly the aforementioned.

1. 1

   Remove the blinds from the wall and pop out the clutch. Most roller blinds will accept a picayune pin on the side opposite the string. Y'all can push this pivot in with a flat-head screwdriver. This volition release the blinds, allowing you to pull them off of the mount. Once you have the blinds off, popular the clutch (the part with the concatenation) off.^[1]

   • Employ a apartment-head screwdriver to pop the clutch off, if needed.
   • This method is meant for blinds that accept ball-and-concatenation style cords; they look similar to the bondage establish on cardinal chains and dog tag necklaces.

2. 2

   Pull the chain out. Search the chain for the connector get-go. Depending on the style, y'all may be able to pop one of the ends out of the connector. Sometimes, however, you will have to popular open the connector, then pull the chains out.^[2]

   • Put the connector into a safety place then that you lot don't lose it.

   Advertisement

3. three

   Thread one finish of the chain upward through the baby-sit. Hold the clutch with the barrel facing up and the base facing downwards. Slide the tip of the chain through the left side of the guard.^[3]

4. iv

   Press the chain into the pulley teeth. Hold nigh an inch (ii.54 centimeters) of then of the concatenation against the pulley teeth. Press downwardly on information technology with your thumb until they pop into place.^[4]

5. 5

   Rotate the caster teeth and popular the chain into identify. Proceed rotating the pulley and popping the concatenation in bit-past-chip until the tip of the chain reaches the left side of the baby-sit.^[five]

6. six

   Pull the chain through the clutch. Rotate the pulley teeth until the chain comes out of the right side of the guard. Grip the concatenation with your fingers or a pair of pliers, then pull down on it. The chain should at present exist fed through the clutch, with both ends dangling out of the clutch.^[6]

7. 7

   Reassemble the blinds and hang them support. Popular the clutch back into the blinds start, then hang the blinds back up on the wall.

8. 8

   Reassemble the concatenation. Feed the chain through the lesser roller, then bring both ends together. If this is a new chain, you may demand to trim it downwards first. Fit the connector over both ends, then snap information technology shut.^[7]

   • If this is a new string, you may need to trim it down commencement.^[8]

   Advertisement

1. 1

   Remove the blinds and the clutch. Virtually roller blinds will have a pivot that you push in with a flat-head screwdriver. This will release the blinds, allowing you to pull them out. Once you have the blinds off, use a flat-head screwdriver to pop off the clutch (the example with the cord in it).^[9]

   • The release pin is typically on the side without the cord.

2. 2

   Pull the string out of the clutch the rest of the manner. Save the string, or get a new 1 intended for the type of roller blind you got. If the cord is already pulled out of the clutch, then you and skip this step.^[10]

3. 3

   Push a loop of string upwards through the guard. Make a 1-inch (2.54-centimeter) loop with the cord. Concord the clutch with the base facing downwards and the barrel facing up. Slide the loop under the guard so that it comes out on pinnacle of the caster teeth.^[11]

4. four

   Pull the loop over the barrel. Take the cord by the loop and pull information technology out far plenty and so that it can fit over the barrel. Sideslip the string down over the butt.^[12]

5. five

   Push the cord into the caster teeth with your pollex. As you push the cord down, information technology may start to bunch upwards at the right side. Gently tug the cord downwardly to smooth as information technology as you push information technology into the teeth.^[xiii]

6. 6

   Rotate the pulley teeth clockwise. The easiest way to practice this would exist with a pencil eraser, but you tin can do it with your pinky finger too. Concord a pencil, eraser-side-downward, confronting the caster teeth. Utilise the pencil to rotate the caster teeth clockwise. Gently tug downward on any cord that bunches up between the guard and the barrel.^[xiv]

7. 7

   Insert the clutch back into the blinds. Hang the blinds support, and then test the cord out. If the cord is not continued, yous will need to adapt the length, trim off the excess, then attach the connector.

   Advertisement

1. one

   Remove the blinds from the wall and pull the clutch off. Unlike other types of clutches, this 1 appears to exist solid. You lot cannot meet the pulley teeth because they are inside the clutch. To remove the blinds and the clutch, do the following:

   • Use a flat-head screw commuter to push button the release pivot. You can typically detect information technology on the side without the string/concatenation.
   • Life the blinds off of the wall mount.
   • Pop the clutch off; employ a apartment-head screwdriver if necessary.

2. ii

   Pinch the pins together at the top of the clutch. Hold your mitt against the bottom of the clutch while you do this. Pinching the pins will release the base of operations of the clutch, and cause information technology to slide out.^[15]

3. 3

   Slide the base of the clutch out. Depending on the brand, the base of operations may slide out all the mode, or information technology may slide out partway. If you take the kickoff type, only slide the base out far enough so that you can see the pulley teeth and the chain.^[xvi]

4. 4

   Pull the chain out. If y'all are going to thread a new chain, take this time to get it out. Practise not cut down the new concatenation down simply yet, however.^[17]

5. v

   Loop the chain effectually the roller teeth. Make a loop with the chain big plenty to fit over the base. Drape the chain effectually the base. Make sure that the ends of the chain come out of the notched part on the clutch.^[18]

6. vi

   Slide the clutch close. Some clutches snap shut on their own. Others have a pin at the bottom that you demand to push button in to lock the two pieces together.^[xix]

7. 7

   Reassemble the blinds. Pop the clutch back into the blinds, then hang the blinds back upwardly. Loop the concatenation effectually the bottom roller, and adjust the length, if needed. You can adjust the length past opening the connector on the chain, trimming the chain down, and then snapping the connector back close.

   Advertisement

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

• Each brand will exist a little different; your specific set of roller blinds may be assembled differently. In this case, try to locate the manual that came with your blinds.

• Don't trim likewise much off of the chain; you want information technology to exist somewhat slack.

Thank you for submitting a tip for review!

Ad

Things You lot'll Need

• Apartment-head screwdriver
• Replacement cord or chain (if needed)
• Scissors or wire cutters (if needed)

About This Article

Article Summary 10

It's easy to replace the chain or cord on roller blinds that accept become loose or and so worn that they need to be replaced. To rethread a roller blind rope cord, outset by removing the blinds from the wall and popping out the clutch, which is the example with the cord in it. Adjacent, pull the string out of the clutch the rest of the way. And then, make a 1-inch loop with the cord, concur the clutch with the base facing down, and slide the loop nether the guard until information technology comes out on top of the pulley teeth. Accept the string by the loop and pull information technology out far enough then yous tin can sideslip it down over the barrel. You lot tin then push the cord into the pulley teeth. Rotate the pulley teeth clockwise as you gently tug down on any string that bunches upwards between the guard and barrel. Finally, insert the clutch dorsum into the blinds and hang them back up. To acquire how to rethread a chain-way cord, go along reading!

Did this summary assist you?

Thank you to all authors for creating a folio that has been read 149,393 times.

Did this commodity help you?

Source: https://www.wikihow.com/Rethread-a-Roller-Blind-Cord

Posted by: schofieldcolooter.blogspot.com

Share this post